A: The white component is a Terminal Position Assurance lock or front retainer. Its purpose is to provide secondary locking security. Once the crimped female terminals are clicked into the main gray housing, this white retainer is pushed inward to lock the pins permanently in place, preventing them from backing out under heavy mechanical pull or road vibration.

A: Yes, the 6189-0372 is a fully sealed, waterproof automotive connector featuring an internal silicone rubber seal. Due to its superior resistance to water, moisture, and dust, it is widely utilized in exposed high-risk areas such as engine compartments, wheel well speed sensors, chassis harnesses, and oxygen sensor links.

A: Yes, this connector is widely used across prominent automotive brands that employ Sumitomo electrical wiring systems. Its official factory part name is 11292W9A04F-GR, which directly corresponds to the 6189-0372 procurement code.

A: Thanks to its IP67 rating and AEC-Q200 certification, the 6180-2185 is ideal for exterior automotive applications where water and vibration are common, such as side turn signals, fog lamps, temperature sensors, and chassis-mounted wiring.

A: The 6180-2185 is compatible with Sumitomo’s standard female crimp terminals for 20–22 AWG (0.5–0.85 mm²) wire. To maintain the IP67 waterproof seal, ensure you use the corresponding wire seals (Grommets) during assembly.

A: Yes, when properly mated with its male counterpart and assembled with the correct wire seals, the IP67 protection provides excellent resistance to moisture ingress, including high-humidity environments and standard automotive spray conditions.

A: Yes. Since the 8240-0531 is a “Sealed” type terminal, it must be used with a compatible rubber wire seal (Grommet) and inserted into a waterproof connector housing to achieve its full IP rating against moisture and dust.

A: Terminal compatibility is highly specific. While it is designed for Sumitomo Waterproof Series housings, it may fit certain OEM-equivalent housings. We recommend verifying the dimensions of the terminal cavity or consulting our technical team for compatibility confirmation.

A: Tin plating provides an excellent balance of conductivity and cost-effectiveness while offering a high level of protection against atmospheric corrosion. For the -40°C to 120°C range, it ensures stable contact resistance, which is critical for signal-level connections in automotive sensors.

A: The 6189-1240 is designed to mate perfectly with the Sumitomo 6188-0779 male housing. Both belong to the TS sealed series, ensuring a fully waterproof wire-to-wire connection.

A: This connector is engineered for durability. While the initial sealing performance is rated at 50kPa Min, it is tested to maintain at least 30kPa Min even after rigorous environmental and durability aging tests, making it suitable for long-term automotive use.

A: Yes. The PBT (Polybutylene Terephthalate) material used in the 6189-1240 is highly resistant to common automotive chemicals, including engine oil, brake fluid, and gasoline, ensuring the housing remains stable in engine bay environments.

A: Yes. This connector belongs to the MT Sealed Series and is designed with an initial sealing pressure of 49.0kPa, making it highly resistant to the water and oil splashes typically found in engine bays

A: The 6187-2171 (Male) is designed to mate perfectly with the Sumitomo 6180-2181 (Female) connector. Both belong to the 2.3mm (090) MT Sealed Series.

A: The terminal itself is a metal contact; however, it is designed for Sealed Applications. To achieve IP67 or IP69K ratings, it must be used within a compatible Sumitomo TS-series sealed housing along with appropriate wire seals (rubber bungs).

A: The 8240-0287 is optimized for signal and low-power applications (Current Rating ≥5A). For high-current power distribution, we recommend larger formats (e.g., TS 2.3mm or 4.8mm series) to avoid excessive heat buildup.

A: This terminal is designed for thin-wall automotive wires like AVS or AVSS 0.5mm². Using the correct wire size is crucial to maintaining the mechanical retention and sealing integrity required by automotive standards.

A: This housing is compatible with Sumitomo TS series 0.64mm (025) female terminals. Please select the terminal based on your wire gauge (typically 0.13mm² to 0.50mm²) to ensure a secure fit and optimal electrical contact within the 32 cavities.

A: No, the 6098-4013 is an unsealed (non-waterproof) housing. It is designed for protected interior environments, such as inside the dashboard or within sealed electronic control boxes, where it is not exposed to direct moisture or contaminants.

A: The TS series is designed with precise keying and a positive latching mechanism. You will feel and hear an audible “click” when the female housing is fully seated with its male counterpart. Additionally, using a TPA (Terminal Position Assurance) feature helps verify that all 32 terminals are correctly locked before mating.

A: This female housing is designed to mate with several TS series male components, including 6098-6805, 6098-6810, and 6098-7102. Using these verified mating parts ensures perfect alignment of the 28 pins.

A: No, the 6098-4756 is an unsealed (non-waterproof) connector. It is primarily used for cabin-side wiring harnesses, such as behind the dashboard, where it is protected from direct water exposure.

A: The TS Series 0.64mm system typically supports wire ranges from 0.13mm² to 0.50mm² (AWG 26-20). The exact fit depends on the specific TS series female terminal you choose to crimp onto your wires.

A: The TPA (Terminal Position Assurance) is a secondary lock that is inserted after the terminals are crimped and seated. It ensures that if a terminal isn’t fully inserted, the lock won’t close, preventing intermittent connections or field failures caused by terminal back-out.

A: Yes. The combination of PBT housing material and silicone rubber seals makes it highly resistant to the vibrations, heat, and fluids typically found in automotive engine and chassis applications.

A: This housing is designed for 2.3mm (.090) flat socket terminals. It supports wire sizes ranging from 0.30 to 2.00 mm², making it compatible with a wide range of automotive wire gauges for power and signal distribution.